Children being supervised not to play with the appliance.
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliances by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
Carefully read this manual before using this appliance.
Ensure that you know how the appliance functions and how to operate it.
Maintain the appliance in accordance with the instructions to ensure that it functions properly.
Keep this manual with the appliance. If the appliance is to be used by a third party, this instruction
manual must be supplied with it.
The safety instructions do not by themselves eliminate any danger completely and proper
accident prevention measures must always be used.
No liability can be accepted for any damage caused by non-compliance with these instructions
or any other improper use or mishandling.
Do not use this appliance if it has been dropped or damaged in any way, or if the supply cord
is damaged.
1 x Appliance Base (Motor Unit), 1 x Food Pusher, 1 x Feed Chute, 1 x Fine Grating Cone,
1 x Medium Grating Cone, 1 x Coarse Grating Cone, 1 x Thin Slicing Cone, 1 x Thick Slicing Cone
1 x Instruction Manual
Confirm all parts before disposing of carton. Safely dispose of all plastic bags and other packaging
components. They may be potentially dangerous to children.
Model : SHB 3068
Voltage: AC230V, 50Hz
Power: 150 Watts
Max Continuous Use: 2 Minutes
When using electric appliances always observe safety regulations where applicable to reduce
the risk of fire, electric shock and personal injury.
Always check that the power supply corresponds to the voltage on the rating plate.
Supply Cord and Plug
Always unplug from mains supply when not in use. Do not abuse or damage the power cord.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or
a similarly qualified person in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.
Do not immerse appliance in water. Do not immerse any part of the motor unit or
supply cord in water. Do not use with wet hands or use in damp situations.
Use and Environment
Do not use outdoors. Place the Base on a flat, level, stable surface. Do not let the cord hang
over the edge of any table or bench top. Do not leave in direct sunlight as this may damage the
plastic. Do not continuously operate the appliance for more than 2 minutes. After 2 minutes of
continuous use, switch off and allow the appliance to cool for a minute. This appliance is intended
for household domestic use only. Do not use this appliance for anything cither than its intended
Injury Precaution
WARNING: Potential injury from misuse! Avoid contact with all moving parts. Switch off the
appliance and disconnect from supply before changing accessories or approaching parts that
move in use. Care shall be taken when handling the sharp grating S cutting blades, and during
cleaning. Always disconnect the appliance from the supply if it is left unattended and before
assembling, disassembling or cleaning.
Double Insulation Safety
This appliance is double insulated for your protection. Do not attempt to repair a double insulated
Damaged or Dropped
Always inspect your appliance before use. Check parts are correctly attached. Do not use this
appliance if it has been damaged, dropped, left outdoors or dropped in water. Return it to an
authorized service dealer for examination and repair
Store in a Safe Place
When not in use store your appliance and all its accessories and instruction manual in a safe
and dry place.
A. Food Pusher
B. Feed Chute
C. Fine Grating Cone
D. Thin Slicing Cone
E. Medium Grating Cone
F. Coarse Grating Cone
G. Thick Slicing Cone
H. Appliance Base (Motor Unit)
I. Handle
J. ON/OFF Switch
Before First Use
Carefully unpack your appliance and remove all accessories. Wash them in warm, soapy water
then rinse and dry with a dry towel. Carefully wipe the exterior of the base if necessary.
WARNING: Do not immerse the appliance base in water or any other liquids.
Using the Electric Slicer & Grater
• Attach the Feed Chute to the Appliance Base. This is done by holding the Feed Chute at a 45
degree angle to the right, inserting it in to the socket on the Appliance Base, then rotating it
45 degrees back to the left so that it is locked in to place in the upright position.
• Select a cone suitable for the slicing or grating task you require and fit it onto the star shaped
drive mechanism at the back of the Feed Chute. Rotate it slightiy clockwise to hold it in place.
• Cut the ingredients into pieces that will fit into the Feed Chute and place a suitable container
under the outlet.
• Connect the appliance to a suitable 220 -240V ~ 50Hz power outlet socket
• Press the ON/OFF button once or twice to ensure that the Cone has locked into place and
turns freely.
• Make sure that the Pusher has been removed from the Feed Chute, and then insert the precut food through the top of the Feed Chute.
• Press and hold down the ON/OFF button to activate the motor then slowly push the food down
with the pusher. Do not exert too much pressure on the pusher, as this could affect the quality
of the end result and could even cause damage to the appliance.
- Turn off by releasing the ON/OFF button.
• To remove the cone unlock the Feed Chute by rotating it 45 degrees to the right then lock it
back into place by rotating 45 degrees back to the left. The Cone can now be easily removed.
• Remember to unplug the unit from the power outlet when it is not in use, changing parts or
is left unattended.
• Always clean the product immediately after each use. Disassembly is reversal of assembly
Important: This appliance is designed for short term operation only. Do not run continuously
for more than 2 minutes. After 2 minutes stop and rest for I minute to allow the appliance to
Note: The first time this appliance is used there may be a small amount of smoke and odour.
This is normal and is due to the protective coating placed on the motor at manufacture to protect
it during shipping.
Tip: For best results use firm ingredients. If the ingredients are too soft the will clump together
and accumulate in and around the cone. If the ingredients are too hard the appliance and cones
may become damaged.
Cone Selection
The Fine Grating Cone can be used for grating parmesan cheese, nuts and spices.
The Medium Grating Cone can be used for grating cheese, carrots, breadcrumbs.
The Coarse Grating Cone can be used for grating cheese, carrots, courgettes, onion.
The Thin Slicing Cone can be used for slicing beetroot, apples, celery.
The Thick Slicing Cone can be used for slicing cucumbers, carrots, potatoes.
Regular maintenance of your appliance will keep it safe and in proper operational order.
Do not attempt to service this appliance. If it is faulty in any way, please follow the instructions
on the enclosed warranty card.
Before cleaning
When not in use or before cleaning, always disconnect the appliance from the mains supply.
The accessories should be separated from the base of the appliance before cleaning. DO NOT
CAUTION: Care is needed when handling the sharp cutting blades, especially during cleaning.
Always clean the product immediately after each use. Rinse off food any scraps then thoroughly
wash parts in warm, soapy water (a soft nylon brush may be helpful) then rinse and dry with a
dry towel. Do not use any abrasive cleaners or harsh solvents. The Feed Chute and Cones can
be washed in a dishwasher on the top rack. Clean the base by wiping it with a damp cloth.
Figure 1
Figure 2
Choose the cone which corresponds to the desired use.
1. Fit the cone holder (B) on the motor unit unit (H) (Fig.1) by giving it a quarter turn to the left
2. Place the chosen cone into the opening at the front of the holder (B). The cone should be
correctly positioned all the way into the drive (Fig.3).
Figure 4
Figure 5
Figure 6
3. Plug in the appliance.
4. Press the On/Off switch (J) once or twice to lock the cone (Fig.4).
WARNING: Press the On/Off switch first before inserting food into the feeder (Fig.5).
5. Insert the food through the feed chute (B) and push the food down using the pusher (A) (Fig.6).
De¤erli Müflterimiz,
En uygun fiyata en iyi ürünü vermenin yan› s›ra; en iyi hizmeti vermenin de
önemli oldu¤una inan›yoruz. Bu nedenle siz bilinçli tüketicilere daha yak›n
olabilmek için, internet adresimizdeki eriflim formlar›n›n yan› s›ra, tüketici
dan›flma hattımızı da hizmetinize açm›fl durumday›z.
444 66 86
0800 211 50 21
Tüketici Dan›flma Hattımızı,
- Hafta içi her gün 08.00-18.00 saatleri aras›nda arayabilir; istek, öneri ve
flikayetlerinizi firmam›za iletebilirsiniz.
Tüketicinin Dikkatine:
Ürünlerimizle ilgili hizmetleri tam olarak alabilmek için afla¤›daki önerilere
uyman›z› rica ederiz:
1. Ürünü ald›¤›n›zda Garanti Belgesini mutlaka yetkili sat›c›n›za onaylatt›r›n›z.
2. Ürünü kullanma k›lavuzunda belirtilen hususlara göre kullan›n›z.
3. Ürününüzle ilgili hizmet talebiniz oldu¤unda yukar›daki telefon
numaralar›ndan, Tüketici Danıflma Hattına baflvurunuz.
4. Ürünü promosyon arac›l›¤› ile edinmiflseniz, ürüne ait garanti belgesini en
yak›n yetkili servisimize giderek onaylatt›r›n›z.
5. Teknik servisteki ifliniz bitti¤inde "Yetkili Servis Hizmet Fifli" almay›
unutmay›n›z. Alaca¤›n›z bu Hizmet Fifli, ileride ürününüzde meydana
gelebilecek herhangi bir sorunda size yarar sa¤layacakt›r.
S E R V ‹ S
Kap›dan Kap›ya Ücretsiz Servis Kampanyam›z dâhilinde Yurtiçi Kargo Firmas› ile iflbirli¤i içerindeyiz. Tüketicimiz
taraf›ndan sat›n al›nan ürünün fiyat› ne olursa olsun, Tüketicimiz ürün ile ilgili garanti kapsam›na giren herhangi
bir problem yaflad›¤›nda, 444 66 86 numaral› Tüketici Danıflma Hattımızı aramas› ve kay›t b›rakmas› yeterlidir.
Bu süreçten sonra Tüketicimizin ürünü ücretsiz olarak Yurtiçi Kargo taraf›ndan Tüketicimizin bulundu¤u adresten
al›n›p, 10• ifl günü içerisinde ürün çal›fl›r bir vaziyette, yine Tüketicimize Yurtiçi Kargo arac›l›¤› ile adresine teslim
edilmektedir. 10 ifl günü içerisinde sorunu çözülemeyen ürünler ise, yenisi ve/veya bir üst modeli ile de¤ifltirilmektedir.
Tüm bu süreçte Tüketicilerimizden hiçbir ücret talep edilmemektedir.
(•Ürünün servis garanti süresi, Yurtiçi Kargo ürünü Sinbo Fabrikas›’na teslim ettikten sonra bafllar.)
- 50 -
- G A R A N T ‹ fi A R T L A R I 1) Garanti süresi,mal›n teslim tarihinden itibaren bafllar ve 2 y›ld›r.
2) Mal›n bütün parçalar› dahil olmak üzere tamam› Firmam›z›n garanti kapsam›ndad›r.
3) Mal›n garanti süresi içerisinde ar›zalanmas› durumunda, tamirde geçen süre garanti
süresine eklenir. Mal›n tamir süresi, 20 iflgününü geçemez. Bu süre mala iliflkin ar›zan›n
servis istasyonuna, servis istasyonunun olmamas› durumunda, mal›n sat›c›s›, bayii,
acentesi, temsilcili¤i, ithalatç›s› veya imalatç›s›-üreticisinden birine bildirim tarihinden
itibaren bafllar. Tüketicinin ar›za bildirimini; telefon, faks, e-posta, iadeli taahhütlü mektup
veya benzeri bir yolla yapmas› mümkündür. Ancak, uyuflmazl›k halinde ispat yükümlülü¤ü
tüketiciye aittir. Mal›n ar›zas›n›n 10 ifl günü içerisinde giderilememesi halinde, imalatç›üretici veya ithalatç›; mal›n tamiri tamamlan›ncaya kadar, benzer özelliklere sahip baflka
bir mal› tüketicinin kullan›m›na tahsis etmek zorundad›r.
4) Mal›n garanti süresi içerisinde gerek malzeme ve iflçilik, gerekse montaj hatalar›ndan
dolay› ar›zalanmas› halinde, iflçilik masraf›, de¤ifltirilen parça bedeli ya da baflka herhangi
bir ad alt›nda hiçbir ücret talep etmeksizin tamiri yap›lacakt›r.
5) Tüketicinin onar›m hakk›n› kullanmas›na ra¤men mal›n;
• Tüketiciye teslim edildi¤i tarihten itibaren, garanti süresi içinde kalmak kayd›yla, bir y›l
içerisinde en az dört defa veya imalatç›-üretici ve/veya ithalatç› taraf›ndan belirlenen
garanti süresi içerisinde alt› defa ar›zalanmas›n›n yan› s›ra, bu ar›zalar›n maldan
yararlanamamay› sürekli k›lmas›,
• Tamiri için gereken azami süresinin afl›lmas› ,
• Firman›n servis istasyonunun, servis istasyonunun mevcut olmamas› halinde s›rayla
sat›c›s›, bayii, acentesi temsilcili¤i ithalatç›s› veya imalatç›-üreticisinden birisinin
düzenleyece¤i raporla ar›zan›n tamirini mümkün bulunmad›¤›n›n belirlenmesi, durumlar›nda
tüketici mal›n ücretsiz de¤ifltirilmesini, bedel iadesi veya ay›p oranda bedel indirimi talep
6) Mal›n kullanma k›lavuzunda yer alan hususlara ayk›r› kullan›lmas›ndan kaynaklanan
ar›zalar garanti kapsam› d›fl›ndad›r.
7) Garanti Belgesi ile ilgili olarak ç›kabilecek sorunlar için Gümrük ve Ticaret Bakanl›¤›
Tüketicinin Korunmas› ve Piyasa Gözetimi Genel Müdürlü¤ü’ne baflvurabilir.
Cihangir Mh. Güvercin Cd. No:4 Haramidere Mevkii Avcılar - ‹stanbul - Türkiye
Ça¤rı Merkezi: 444 66 86 - [email protected]
- 51 -
- SHB 3068 BLENDER -GARANT‹ BELGES‹ Garanti Belge No : 78504
SSHY Belge No : 35274
Garanti Belge Onay Tarihi : 03/02/2010
Garanti Belge Vize Tarihi : 18/01/2012
SSHY Belge Onay Tarihi : 04/04/2012
: Cihangir Mah. Güvercin Cad. No:4 Haramidere Mevkii
Avc›lar / ‹STANBUL
: Ça¤rı Merkezi: 444 66 86
Yetkili Kifli
Ürünün Cinsi
Alt Modeli
Bandrol ve Seri No
Teslim Tarihi ve Yeri
Garanti Süresi
Azami Tamir Süresi
Kullanım Ömrü
Yönetim Kurulu Baflkan›
SHB 3068
2 Yıldır
20 ‹fl Günü
Bakanl›kça belirlenen ve ilan edilen kullan›m ömrü 7 y›ld›r.
(Ürünün fonksiyonlar›n› yerine getirebilmesi için gereken yedek parça temin süresi)
Fatura Tarihi ve No
Teslim Tarihi ve Yeri
‹mza ve Kafle
Bu bölüm, ürünü sat›n ald›¤›n›z Yetkili Sat›c› taraf›ndan imzalanacak ve kaflelenecektir.
Bu belgenin kullan›lmas›na; 4077 say›l› Tüketicinin Korunması Hakkında Kanun ve bu Kanun’a dayan›larak yürürlü¤e konulan Garanti Belgesi
Uygulama Esaslar›na Dair Yönetmelik uyar›nca, TC Gümrük ve Ticaret Bakanlı¤ı, Tüketicinin Korunması ve Piyasa Gözetimi Genel Müdürlü¤ü
tarafından izin verilmifltir.
- 52 -
- TEDAR‹KÇ‹ F‹RMA / EXPORTER United Favour Development Limited
Unit B, 10/F Lee May Building 788-790
Nathan Road, Mongkok, Kowloon, HK.
- UYGUNLUK BEYANI / CE TÜV Rheinland LGA Products GmbH
Tillystraße 2,90431 Nürnberg, Germany
EEE Yönetmeli¤ine uygundur.
AEEE Yönetmeli¤ine uygundur.
Made in P.R.C.
‹mal Y›l› : 2013